EMI Gasket Galvanic Corrosion: Managing Dissimilar Metals in Shielded Enclosures
Knowledge Base

EMI Gasket Galvanic Corrosion: Managing Dissimilar Metals in Shielded Enclosures

The Hidden Failure Mode of EMI Shielding

EMI gaskets rarely fail when new. They fail two or three years after installation, when galvanic corrosion at the gasket-to-flange interface has grown a high-resistance oxide layer across the contact points. Shielding effectiveness that measured 60 dB on the production line drops 20–30 dB at low frequencies, and the product begins radiating at its clock harmonics. Because the corrosion is seasonal and progressive, it slips through spot checks and shows up as field failures in humid and coastal climates—exactly the markets of Southeast Asia.

The Electrochemistry in Brief

When two dissimilar metals touch in the presence of an electrolyte—condensation, salt fog, humid air with ionic contamination—the less noble metal becomes the anode and corrodes. The galvanic series ranks the usual enclosure materials: silver and gold are most noble; stainless steel (passivated), nickel, and tin are intermediate; aluminum, zinc, and cadmium are active. A conductive elastomer filled with silver-plated aluminum beads clamped to a bare aluminum flange is nearly ideal galvanically. The same gasket on a zinc-plated steel flange creates a strong couple that attacks the zinc coating, leaving white corrosion products that push the gasket off the surface.

Classic Bad Pairings

  • Silver-filled silicone on aluminum: the filler is noble, the flange active. In salt fog, aluminum oxide grows under the gasket line. Mitigate only if the flange is chromate-conversion coated (still marginal) or a nickel underplate is applied.
  • Tin-plated lids on nickel-plated bodies: workable in benign environments, but tin whiskers and fretting under vibration degrade contact over time.
  • Stainless fasteners through aluminum flanges: acceptable with washers and conversion coating; disastrous on bare aluminum in marine service.

Design Rules That Prevent Corrosion

Match the gasket filler to the flange

Use the filler-metal pairing table from gasket vendors: aluminum-filled elastomer for aluminum flanges, tin-plated copper beryllium finger stock for tin or nickel surfaces, nickel-graphite for painted or plated steel. Silver-filled gaskets are reserved for silver- or gold-plated RF flanges where the contact resistance matters most.

Control the environment at the seam

A gasket ca

ot survive standing water. Design the seam so the gasket line is not the lowest point; add drip edges, and orient horizontal seams with the gasket facing down or inward. For outdoor enclosures, combine the EMI gasket with an adjacent environmental (non-conductive) gasket in a dual-seal arrangement, so the EMI gasket stays dry while the outer seal takes the weather.

Specify surface finishes

Chromate conversion per MIL-DTL-5541 Class 1A on aluminum, tin or nickel plating on steel, and avoidance of bare zinc in coastal service are cheap insurance. Paint the flange and you insulate it—conductive epoxy primers or masked plating windows are the workaround.

Compression and fastener spacing

Over-compression cracks conductive filler particles out of the elastomer surface; under-compression leaves micro-gaps that wick moisture. Hold the vendor’s deflection window (typically 10–30% for elastomers) with positive stops or sized grooves, and space fasteners so flange deflection between bolts stays within 0.05–0.1 mm.

Verification and Maintenance

Specify DC contact resistance spot checks (milliohm range, per vendor datasheet) at 25%, 50%, and 100% of rated compression on incoming gaskets, and add a salt-fog exposure test (48–96 h, ASTM B117) for critical programs. In the field, inspect gasket seams a

ually in tropical installations: white or green powder at the seam line is early galvanic attack, and reseating with a fresh gasket costs little if caught in year one.